 |
2 Bore X 12 Stroke
Cissoko
| Quantity: | |
|---|---|
Experience unmatched power and precision with our high-performance Green Hydraulics Welded Double Acting Hydraulic Cylinder with a 2-inch bore and 12-inch stroke with clevis ends and 2500 PSI. This cylinder is an optimal welded-type replacement for the tie rod cylinder. Ideal replacement for farming equipment and various other applications.
22.25" Standard Closed Center Distance and Wide Range Adjustment: Under industry standard, the pin-to-pin center distance when fully retracted is 22.25 inches . Combined with a 12-inch long stroke, it can achieve smooth push and pull over a wide range, perfectly meeting the layout requirements of light and medium-sized agricultural implements for large-angle deflection or long-distance lifting.
2" Compact Bore and Efficient Response: The 2-inch bore delivers approximately 7,854 pounds (about 3.5 tons) of thrust while requiring a very small volume of hydraulic fluid per cylinder stroke. Even with a longer stroke of 12 inches, it achieves an extremely agile and rapid extension/retraction response, with low system flow requirements and excellent fuel economy.
Fully welded longitudinal buckling-resistant body: The cylinder head and lugs adopt an integral fully welded structure, abandoning the traditional tie rod and screw design. This high-strength, heavy-duty steel body provides excellent longitudinal rigidity and overall stability , effectively preventing local bending or breakage of long-stroke cylinders under full extension and heavy load conditions.
High-strength hard chrome plated piston rod: The piston rod surface is precision rolled and tempered and covered with a high-thickness hard chrome electroplated layer. It has excellent bending resistance and rust and corrosion resistance , and can withstand the wear of outdoor wind, sand, dust, mud and acidic fertilizers for a long time, protecting the core oil seal from scratches.
SAE 8 ORB Dual End-Face Sealing: All oil ports utilize modern SAE 8 O-ring straight thread (ORB) interfaces , internally equipped with high-end multi-component piston seals. This completely eliminates "micro-leakage" and "dripping" under high-pressure operation , maintaining equipment cleanliness while effectively preventing the intrusion of mud and sand from harsh external environments.
SKU | Bore | Stroke | Rod Ø | Retracted | Extended | Pin Ø | Port Size | Column Load | Weight |
|---|---|---|---|---|---|---|---|---|---|
WBC 2x8 | 2 in | 8 in | 1.125 in | 18.25 in | 26.25 in | 1 in | SAE 8 | 7,850 lbs | 15 lbs |
WBC 2x8 ASAE | 2 in | 8 in | 1.125 in | 20.25 in | 28.25 in | 1 in | SAE 8 | 7,850 lbs | 15 lbs |
WBC 2x10 | 2 in | 10 in | 1.125 in | 20.25 in | 30.25 in | 1 in | SAE 8 | 7,850 lbs | 16 lbs |
WBC 2x12 | 2 in | 12 in | 1.125 in | 22.25 in | 34.25 in | 1 in | SAE 8 | 7,850 lbs | 17 lbs |
WBC 2x14 | 2 in | 14 in | 1.125 in | 24.25 in | 38.25 in | 1 in | SAE 8 | 7,850 lbs | 19 lbs |
WBC 2x16 | 2 in | 16 in | 1.125 in | 26.25 in | 42.25 in | 1 in | SAE 8 | 7,850 lbs | 20 lbs |
WBC 2x18 | 2 in | 18 in | 1.125 in | 28.25 in | 46.25 in | 1 in | SAE 8 | 7,850 lbs | 21 lbs |
WBC 2x20 | 2 in | 20 in | 1.125 in | 30.25 in | 50.25 in | 1 in | SAE 8 | 7,850 lbs | 23 lbs |
WBC 2x24 | 2 in | 24 in | 1.125 in | 34.25 in | 58.25 in | 1 in | SAE 8 | 6,950 lbs | 25 lbs |
Applications
Primary Vehicle Applications
Standard Dump Trucks (Class 7 & Class 8): Widely used on 10-wheelers, tri-axle, and quad-axle dump trucks with body lengths ranging from 14 to 18 feet .
Dump Trailers & End Dumps: Installed on medium-sized end dump semi-trailers or heavy-duty pull trailers requiring an aggressive tilt angle to shed stubborn
Pup Trailers: Commonly used on independent dump pup trailers towered behind a standard dump truck to maximize total hauling capacity.
Construction & Aggregates: Lifting heavy loads of gravel, crushed stone, sand, and asphalt on rugged construction sites.
Demolition & Waste Management: Tipping large-volume truck bodies carrying concrete debris, scrap metal, and heavy municipal waste .
Mining & Earthmoving: Operating on site-specific support vehicles hauling heavy soil, overburden, and mineral ores .
Agriculture: Used on specialized agricultural bulk trailers for high-volume dumping of grain, silage, and fertilizers .
2 Bore X 12 Stroke Ag Clevis Hydraulic Cylinders are typically packaged securely to prevent damage during transit. The packaging includes:
Protective Wrapping: To safeguard the pump from environmental damage.
Custom Crates: For larger, heavier pumps, ensuring safe handling.
Documentation: Includes installation, maintenance instructions, and warranty details.
Delivery time depends on the model, customizations, and location but typically ranges from 2 to 6 weeks from the order date.
answer:
Fully retracted (closed) center distance: 22.25 inches (approximately 565 mm).
Fully extended center distance: 34.25 inches (approximately 870 mm).
Overall length/hydraulic volume: The overall length is approximately 24.25 inches, and the hydraulic fluid volume required for a single full-stroke extension is approximately 0.65 gallons (or quarts).
A: Special attention is needed. Compared to 6-inch or 8-inch short-stroke piston rods, 12-inch stroke piston rods are prone to lateral instability or bending when fully extended and subjected to enormous longitudinal thrust. When selecting a piston rod, ensure that the load trajectory is completely parallel to the cylinder to avoid bearing non-axial eccentric side loads. If extremely high thrust is required, it is recommended to check whether the piston rod diameter (usually 1.125" or 1.25") meets the equipment's compressive strength design.
answer:
At a standard pressure of 2,500 PSI (as in standard agricultural configuration), it provides approximately 7,850 pounds (about 3.5 tons) of thrust and approximately 5,390 pounds of pull.
If it is a high-pressure type (some models are rated up to 3,500 PSI ), its thrust can be increased to about 9,400 pounds (about 4.2 tons) .
A: The SAE 8 ORB (O-Ring Boss) connector uses a face O-ring hard seal, which virtually eliminates slow leakage under high-pressure and vibration conditions, performing far better than older tapered pipe threads. If your old hose is NPT specification and cannot be directly screwed on , you only need to purchase two additional " SAE 8 external thread to NPT internal thread " adapters for a seamless connection.
A: No cutting or welding is required. The front guide sleeve (Gland) of a fully welded hydraulic cylinder typically has precision threads . In case of minor oil leakage, you can use a special spanner wrench to unscrew the front cover, remove the piston rod assembly, and simply replace it with the matching seal kit to restore it to its original condition, saving the cost of replacing the entire hydraulic cylinder.
6. Do you provide OEM or customized services
Yes, we support OEM and customization, including nameplate, packaging, and specific performance requirements. Send us your drawings or specifications for evaluation.
2 Bore X 12 Stroke Ag Clevis Hydraulic Cylinders are manufactured in compliance with international standards, ensuring high performance and reliability:
ISO 9001: Certified for quality management systems.
CE Certification: Ensures compliance with European safety, health, and environmental protection standards.
RoHS Compliance: Ensures the Cylinders does not contain hazardous materials.
Factory Testing: Every Cylinders is rigorously tested for performance, pressure, and leak integrity before shipping.
1.What's our advantages?
Factory established in 2005;
With a great deal of production experience;
80+ employees become the professional team;
Constant updated ERP system ensure efficiency of work;
Sophisticated equipment ehanced the accuracy of products;
Professional salesmen provide the greast service;
With a large number of famous customers all over the world;
Great after-sales service;
With the long term cooperation with famous logistics and express company in China,provide the better goods service.
Small order/sample order,full payment in advance; Big orders send the first payment 30% before the production,and the balance before shippment.We'll show the photos of the products and packages before delivery.
Of course we can. Just send me your logo we can make it for you.
America(40.5%):USA, Canada, Argentina, Brazil
Europe(30.8%):Italy,Germany,England,Holland,Spain,Swiss,Finland,Russia,Poland.
Asia(23.5%):Korea,singapore,India,Turkey,Vietnam,Saudi Arabia,Syria, Israel,Lebanon.
Others(5.8%).
The Cissoko hydraulic pump manufacturing facility is a specialized industrial plant that focuses on producing hydraulic pumps and related components. These factories are equipped with advanced machinery and technology to fabricate high-quality pumps designed for a wide range of applications, from heavy equipment and machinery to automotive and industrial systems.
The production process typically involves precision engineering, where raw materials like metals and alloys are processed into pump components such as gears, pistons, cylinders, and seals. These parts are then assembled into fully functional hydraulic pumps, which are tested for performance and quality control to ensure reliability, efficiency, and durability under various working conditions.
Cissoko Hydraulic's manufacturing facilities for hydraulic pumps maintain stringent quality standards, often adhering to international certifications, to meet the expectations of customers in industries such as construction, agriculture, automotive, and manufacturing.
All hydraulic pumps produced by Cissoko Hydraulic have undergone compliance testing, ensuring their quality and reliability.
To meet the diverse needs of different industries, the Cissoko hydraulic offer customization options, such as specialized seals, materials, and pump configurations. These facilities often work closely with engineering teams to develop tailored solutions for specific applications, from high-pressure systems to low-flow, high-efficiency pumps.
Each pump undergoes a rigorous quality control process, where pressure tests and performance assessments are conducted to ensure that the pumps meet the required standards for flow rate, pressure capacity, and durability.
