 |
HWN 12000
cissoko
| Quantity: | |
|---|---|
The Runva HWN 12000 isThis industrial-grade, high-tonnage hydraulic self-rescue and recovery winch is designed for heavy-duty full-size 4x4 off-road vehicles, commercial flatbed trailers, road clearing vehicles, and special-purpose engineering vehicles. It is powered directly from the vehicle's hydraulic steering system, PTO (Power Take-Off) system, or an independent auxiliary hydraulic pump, completely eliminating common electric winch malfunctions such as battery depletion, solenoid valve burnout, and motor overheating. This model delivers a continuous, powerful hydraulic torque of up to **12,000 lbs (approximately 5,443 kg),** making it ideal for high-frequency, uninterrupted operations in harsh environments.
Unlimited 100% Commercial Duty Cycle : Because its operation is entirely driven by vehicle hydrodynamics, there is absolutely no thermal decay inside the winch, nor is it limited by the lifespan of any electrical components . Operators can tow continuously for hours under heavy loads without stopping to allow the motor to cool down.
Excellent adaptability to harsh environments (Fully Submersible) : No electric motor means no carbon brush wear, no broken copper wires, or water ingress into solenoid valves and short circuits. The entire unit uses heavy-duty hydraulic high-pressure seals, allowing the winch to perfectly perform its recovery duties when fully submerged in deep water, swampy mud, or extreme ice and snow .
Failsafe hydraulic fluid locking brake : The automatic hydraulic brake works in close coordination with the mechanical self-locking mechanism. The braking system will immediately lock the rollers the instant the control valve resets and the oil flow stops, achieving zero slippage and zero rollover even when facing a 12,000-pound fully loaded suspension .
The core of the heavy-duty all-steel gearbox : the internal gears are all made of high-strength tempered alloy steel planetary gears , resolutely rejecting plastics or composite materials, and can easily withstand sudden and severe impact loads during off-road recovery.
| Parameter | Specification / Value |
|---|---|
| Rated Line Pull | 12,000 lb (5,443 kg) |
| Hydraulic Motor Displacement | 65 mL/rev |
| Oil Flow | 5–45 L/min |
| Working Pressure | 14 MPa |
| Brake | Automatic Brake |
| Geartrain | 2-Stage Planetary Gear |
| Gear Reduction Ratio | 25.5:1 |
| Clutch Options | Pneumatic, Manual, or Pneumatic and Manual |
| Cable Size (Diameter × Length) | Ø7/16 in × 83.7 ft (Ø11 mm × 25.5 m) |
| Drum Size (Diameter × Length) | Ø2.8 in × 8.5 in (Ø72 mm × 216 mm) |
| Mounting Bolt Pattern | 10 in × 4.5 in (254 mm × 114.3 mm), 4 × M12 |
| Net Weight | 139.0 lb (63.0 kg) |
Applications
Service Truck Lifting : Mounts directly onto custom davit cranes or articulating crane arms on field service mechanics' trucks to lift heavy engine blocks, transmissions, and industrial pumps.
Tool and Equipment Loading : Installed on utility truck beds to effortlessly hoist heavy weld packs, gas cylinders, and tooling boxes from the ground up onto the vehicle platform.
Overhead Gantry Systems : Affixes to overhead I-beam trolleys or fixed gantry frames to hoist heavy machinery parts, steel fabrications, and raw materials over assembly lines.
Vehicle Maintenance Lifting : Utilized in automotive or heavy equipment workshops to suspend or precisely position unyielding sub-frames and assemblies during repairs.
Watercraft Hoisting : Integrated into dockside davits or small marina cranes to vertically lift jet skis, tender boats, and outboard motors out of the water for dry storage or servicing.
Marine Cargo Handling : Handles loading and unloading operations on utility vessels and cargo docks where a fully sealed, weather-resistant hoisting unit is required.
Heavy Farm Rigging : Mounts inside barns or specialized tractor attachments to safely suspend heavy farm implements, cutter decks, or tractor components for routine blade sharpening or structural maintenance.
Game and Timber Processing : Used on rural work yards to lift large timber logs onto processing benches or hoist large game carcasses onto cleaning racks.
HWN 12000 winch are typically packaged securely to prevent damage during transit. The packaging includes:
Protective Wrapping: To safeguard the pump from environmental damage.
Custom Crates: For larger, heavier pumps, ensuring safe handling.
Documentation: Includes installation, maintenance instructions, and warranty details.
Delivery time depends on the model, customizations, and location but typically ranges from 2 to 6 weeks from the order date.
Answer : It is perfectly matched with heavy-duty off-road expedition vehicles (such as Toyota Land Cruiser, Nissan Patrol, and heavy-duty off-road pickup trucks), commercial medium-sized flatbed trailers, urban recovery vehicles, and agricultural machinery search and rescue vehicles . It is specifically designed for professional recovery scenarios with long single rescue times, high sludge absorption capacity, or dozens of continuous operations per day.
Answer : Yes, but a dedicated hydraulic bypass valve kit must be connected in series. The original power steering pump has a relatively small displacement and pressure, which will reduce the winch's pulling force and speed. To unleash the full 12,000 lbs nominal industrial pulling force, it is strongly recommended to install a high-flow auxiliary hydraulic pump or introduce it into the PTO power system via a transfer case .
Answer : Under no-load conditions, its linear speed may be slightly lower than some high-speed electric racing winches; however, the biggest advantage of a hydraulic winch lies in its "extremely stable linear speed under load ." Electric winches, under heavy loads, may experience a precipitous drop in linear speed or even stall due to motor overheating, while a hydraulic winch, as long as the engine is running and the oil pressure is stable, can pull out heavy objects at a uniform and constant speed.
Answer : It uses a standard 10.0" x 4.5" (254mm x 114.3mm) 4-hole bolt hole spacing, which can be aligned with most commercial front bumpers on the market. However, due to the relatively long lateral depth of the hydraulic motor and the presence of a rigid high-pressure oil pipe connector, it is essential to check the technical drawings before installation to ensure that there is sufficient clearance inside the front bumper.
Answer : Absolutely, and even more suitable than an electric winch. Traditional electric winches typically have brake pads built into the drum, which generates enormous heat during prolonged operation, potentially damaging the nylon rope. Hydraulic winches, on the other hand, rely entirely on a fluid circuit for braking, keeping the drum completely cold during use , which is extremely gentle on the nylon rope. Upgrading simply requires adding a smooth aluminum alloy window (Hawse Fairlead).
6. Do you provide OEM or customized services
Yes, we support OEM and customization, including nameplate, packaging, and specific performance requirements. Send us your drawings or specifications for evaluation.
HWN 12000 winch are manufactured in compliance with international standards, ensuring high performance and reliability:
ISO 9001: Certified for quality management systems.
CE Certification: Ensures compliance with European safety, health, and environmental protection standards.
RoHS Compliance: Ensures the winch does not contain hazardous materials.
Factory Testing: Every winch is rigorously tested for performance, pressure, and leak integrity before shipping.
1.What's our advantages?
Factory established in 2005;
With a great deal of production experience;
80+ employees become the professional team;
Constant updated ERP system ensure efficiency of work;
Sophisticated equipment ehanced the accuracy of products;
Professional salesmen provide the greast service;
With a large number of famous customers all over the world;
Great after-sales service;
With the long term cooperation with famous logistics and express company in China,provide the better goods service.
Small order/sample order,full payment in advance; Big orders send the first payment 30% before the production,and the balance before shippment.We'll show the photos of the products and packages before delivery.
Of course we can. Just send me your logo we can make it for you.
America(40.5%):USA, Canada, Argentina, Brazil
Europe(30.8%):Italy,Germany,England,Holland,Spain,Swiss,Finland,Russia,Poland.
Asia(23.5%):Korea,singapore,India,Turkey,Vietnam,Saudi Arabia,Syria, Israel,Lebanon.
Others(5.8%).
The Cissoko hydraulic pump manufacturing facility is a specialized industrial plant that focuses on producing hydraulic pumps and related components. These factories are equipped with advanced machinery and technology to fabricate high-quality pumps designed for a wide range of applications, from heavy equipment and machinery to automotive and industrial systems.
The production process typically involves precision engineering, where raw materials like metals and alloys are processed into pump components such as gears, pistons, cylinders, and seals. These parts are then assembled into fully functional hydraulic pumps, which are tested for performance and quality control to ensure reliability, efficiency, and durability under various working conditions.
Cissoko Hydraulic's manufacturing facilities for hydraulic pumps maintain stringent quality standards, often adhering to international certifications, to meet the expectations of customers in industries such as construction, agriculture, automotive, and manufacturing.
All hydraulic pumps produced by Cissoko Hydraulic have undergone compliance testing, ensuring their quality and reliability.
To meet the diverse needs of different industries, the Cissoko hydraulic offer customization options, such as specialized seals, materials, and pump configurations. These facilities often work closely with engineering teams to develop tailored solutions for specific applications, from high-pressure systems to low-flow, high-efficiency pumps.
Each pump undergoes a rigorous quality control process, where pressure tests and performance assessments are conducted to ensure that the pumps meet the required standards for flow rate, pressure capacity, and durability.
