 |
HWN 15000I
cissoko
| Quantity: | |
|---|---|
The Runva HWN 15000I is anindustrial-strength, ultra-high-capacity hydraulic recovery winch engineered for heavy commercial flatbed tow trucks, road recovery wreckers, multi-car carriers, and extra-heavy 4x4 expedition rigs. The letter "I" denotes its specialized Internal Integrated Brake design . Driven entirely by fluid flow from a vehicle PTO (Power Take-Off) system or an independent high-output hydraulic pump, this heavy-duty workhorse delivers a massive 15,000 lbs (6,804 kg) single-line pulling capacity. It trades electrical complexity for brute hydraulic torque, providing non-stop pulling capability under the most grueling industrial conditions.
Infinite 100% Commercial Duty Cycle : Because it operates entirely on vehicle fluid dynamics, the winch will never overheat, suffer from electrical relay failure, or drain your vehicle battery . Operators can run the winch under maximum load for hours continuously without stopping, completely outlasting any electric winch.
Failsafe Internal Safety Brake : As an "I" series variant, this model features an optimized internal deadlock brake system inside the oil circuit loop . The moment the fluid control valve returns to neutral and fluid flow ceases, the drum is instantly friction-locked, ensuring zero slip or rollback even under a full 15,000 lbs suspension during trailer ramp loading.
Brute Low-End Crawling Leverage : The combination of a high-displacement hydraulic motor and deep planetary gearing generates unrelenting mechanical torque. It easily breaks the intense suction of deep mud or clay for heavy commercial trucks and armored overlanding rigs.
Complete Underwater Submersibility : Lacking an electric motor means there are no carbon brushes, copper windings, or delicate solenoids to short out. The fully sealed, high-pressure hydraulic circuit allows the winch to operate flawlessly while completely submerged underwater or buried in deep swamp mud .
| Parameter | Specification / Value |
|---|---|
| Rated Line Pull | 15,000 lb (6,804 kg) |
| Hydraulic Motor Displacement | 80 ml/rev |
| Oil Flow Range | 5–60 L/min |
| Working Pressure | 13 MPa |
| Brake Type | Wet-Type Hydraulic Brake |
| Geartrain | 2-Stage Planetary Steel Gear |
| Gear Reduction Ratio | 33.4:1 |
| Clutch Options | Pneumatic, Manual, or Combined Pneumatic/Manual |
| Waterproof Rating | IP54 |
| Wire Rope Size (Diameter × Length) | Ø15/32 in × 87 ft (Ø12 mm × 26.5 m) |
| Drum Size (Diameter × Length) | Ø3.5 in × 8.5 in (Ø89 mm × 217 mm) |
| Mounting Bolt Pattern | 10 in × 4.5 in (254 mm × 114.3 mm), 4 × M12 |
| Net Weight | 132 lb (60 kg) |
Applications
Service Truck Lifting : Mounts directly onto custom davit cranes or articulating crane arms on field service mechanics' trucks to lift heavy engine blocks, transmissions, and industrial pumps.
Tool and Equipment Loading : Installed on utility truck beds to effortlessly hoist heavy weld packs, gas cylinders, and tooling boxes from the ground up onto the vehicle platform.
Overhead Gantry Systems : Affixes to overhead I-beam trolleys or fixed gantry frames to hoist heavy machinery parts, steel fabrications, and raw materials over assembly lines.
Vehicle Maintenance Lifting : Utilized in automotive or heavy equipment workshops to suspend or precisely position unyielding sub-frames and assemblies during repairs.
Watercraft Hoisting : Integrated into dockside davits or small marina cranes to vertically lift jet skis, tender boats, and outboard motors out of the water for dry storage or servicing.
Marine Cargo Handling : Handles loading and unloading operations on utility vessels and cargo docks where a fully sealed, weather-resistant hoisting unit is required.
Heavy Farm Rigging : Mounts inside barns or specialized tractor attachments to safely suspend heavy farm implements, cutter decks, or tractor components for routine blade sharpening or structural maintenance.
Game and Timber Processing : Used on rural work yards to lift large timber logs onto processing benches or hoist large game carcasses onto cleaning racks.
HWN 15000I winch are typically packaged securely to prevent damage during transit. The packaging includes:
Protective Wrapping: To safeguard the pump from environmental damage.
Custom Crates: For larger, heavier pumps, ensuring safe handling.
Documentation: Includes installation, maintenance instructions, and warranty details.
Delivery time depends on the model, customizations, and location but typically ranges from 2 to 6 weeks from the order date.
Answer : It is designed specifically for heavy commercial flatbed recovery tow trucks, tilt-tray car carriers, agricultural machinery transport, tractors, and extra-heavy armored overlanding trucks . Its 15,000 lbs ratings handles extreme vehicle deadweight where lightweight consumer winches would fail or overheat.
Answer : No. Unlike lighter hydraulic models, an industrial 15,000 lbs winch requires a high oil flow up to 60 L/min and maximum pressures up to 15 MPa. Standard consumer light-truck power steering grids cannot provide this volume. It must be plumbed into a dedicated PTO (Power Take-Off) system or an auxiliary high-output commercial pump loop.
Answer : It delivers a highly stable, uniform crawling speed that remains completely constant under maximum resistance. While some electric winches may reel faster when completely unweighted, they slow down drastically and lose power as they heat up, whereas the hydraulic winch maintains full power and consistent speed indefinitely .
Answer : While it shares the industry-standard 10.0" x 4.5" bolt footprint, it is a massive industrial winch weighing significantly more than standard consumer units. Most standard consumer light-truck bull bars cannot physically accommodate the oversized motor depth and external hydraulic hose fittings. A dedicated heavy commercial bumper bar or reinforced trailer chassis mount is required.
Answer : Yes, it is exceptionally safe for synthetic Dyneema lines . Standard electric winches have internal brake shoes that generate immense friction heat inside the drum, which can melt synthetic fibers during long pulls. Since hydraulic winches rely on fluid braking outside the drum core, the cylinder stays completely cool. Just remember to replace the steel roller fairlead with a smooth aluminum hawse fairlead to prevent rope fraying.
6. Do you provide OEM or customized services
Yes, we support OEM and customization, including nameplate, packaging, and specific performance requirements. Send us your drawings or specifications for evaluation.
HWN 15000I winch are manufactured in compliance with international standards, ensuring high performance and reliability:
ISO 9001: Certified for quality management systems.
CE Certification: Ensures compliance with European safety, health, and environmental protection standards.
RoHS Compliance: Ensures the winch does not contain hazardous materials.
Factory Testing: Every winch is rigorously tested for performance, pressure, and leak integrity before shipping.
1.What's our advantages?
Factory established in 2005;
With a great deal of production experience;
80+ employees become the professional team;
Constant updated ERP system ensure efficiency of work;
Sophisticated equipment ehanced the accuracy of products;
Professional salesmen provide the greast service;
With a large number of famous customers all over the world;
Great after-sales service;
With the long term cooperation with famous logistics and express company in China,provide the better goods service.
Small order/sample order,full payment in advance; Big orders send the first payment 30% before the production,and the balance before shippment.We'll show the photos of the products and packages before delivery.
Of course we can. Just send me your logo we can make it for you.
America(40.5%):USA, Canada, Argentina, Brazil
Europe(30.8%):Italy,Germany,England,Holland,Spain,Swiss,Finland,Russia,Poland.
Asia(23.5%):Korea,singapore,India,Turkey,Vietnam,Saudi Arabia,Syria, Israel,Lebanon.
Others(5.8%).
The Cissoko hydraulic pump manufacturing facility is a specialized industrial plant that focuses on producing hydraulic pumps and related components. These factories are equipped with advanced machinery and technology to fabricate high-quality pumps designed for a wide range of applications, from heavy equipment and machinery to automotive and industrial systems.
The production process typically involves precision engineering, where raw materials like metals and alloys are processed into pump components such as gears, pistons, cylinders, and seals. These parts are then assembled into fully functional hydraulic pumps, which are tested for performance and quality control to ensure reliability, efficiency, and durability under various working conditions.
Cissoko Hydraulic's manufacturing facilities for hydraulic pumps maintain stringent quality standards, often adhering to international certifications, to meet the expectations of customers in industries such as construction, agriculture, automotive, and manufacturing.
All hydraulic pumps produced by Cissoko Hydraulic have undergone compliance testing, ensuring their quality and reliability.
To meet the diverse needs of different industries, the Cissoko hydraulic offer customization options, such as specialized seals, materials, and pump configurations. These facilities often work closely with engineering teams to develop tailored solutions for specific applications, from high-pressure systems to low-flow, high-efficiency pumps.
Each pump undergoes a rigorous quality control process, where pressure tests and performance assessments are conducted to ensure that the pumps meet the required standards for flow rate, pressure capacity, and durability.
