 |
HWP 20000YD
cissoko
| Quantity: | |
|---|---|
The Runva HWP 20000YD is anindustrial-strength, ultra-high-capacity heavy-duty hydraulic winch engineered specifically for commercial tow wreckers, heavy tilt-tray recovery beds, massive 4x4 expedition trucks, and severe industrial pulling setups. The designation "YD" highlights its specialized configuration combining a Manual Clutch combined with an Automatic Hydraulic Two-Speed Shifting gearbox or advanced dual-speed infrastructure built for heavy recovery optimization. Driven entirely by auxiliary fluid dynamics rather than high-amperage vehicle batteries, this massive recovery unit outputs an incredible 20,000 lbs (9,072 kg) of single-line crawling torque, providing an infinite 100% cycle duty that outlasts any equivalent electric alternative.
Infinite 100% Commercial Duty Cycle : Since it runs purely on vehicle fluid dynamics instead of electric grids, the system will never overheat, suffer from voltage drops, or trigger thermal shutdown . Operators can continuously pull heavy 9-ton loads back-to-back all day long.
Failsafe Two-Speed Shifting Integration : Features Runva's specialized transmission design where switching between High Speed (6:1) for fast unweighted cable deployment and Low Speed (39:1) for brutal extraction muscle is handled seamlessly, preventing operational errors under full 9-ton strains.
Advanced Internal Wet Brake Safety : Features a specialized multi-disc wet brake fully integrated inside the pressurized oil loop alongside a factory counterbalance valve. The mechanism friction-locks instantly the moment fluid pressure ceases, holding massive suspended assets with zero slip or rollback mid-ramp. [1]
Steel Wire Tensioner (SWR) System : Standard packages ship with a factory pre-installed cable steel wire pressure roller/tensioner . This configuration prevents the loose 14mm line from birdnesting, tangling, or bunching on the drum when running out unweighted.
| Parameter | Specification / Value |
|---|---|
| Rated Line Pull | 20,000 lb (9,072 kg) |
| Hydraulic Motor Displacement | 100 ml/rev |
| Oil Flow Range | 15–75 L/min |
| Working Pressure | 17.5 MPa |
| Brake Type | Screw Multi-Disc Brake |
| Geartrain | 2-Stage Planetary Steel Gear |
| Gear Reduction Ratio | High Speed: 6:1; Low Speed: 39:1 |
| Clutch Options | Pneumatic, Manual, or Combined Pneumatic/Manual |
| Wire Rope Size (Diameter × Length) | Ø9/16 in × 157 ft (Ø14 mm × 48 m) |
| Drum Size (Diameter × Length) | Ø5.4 in × 12.4 in (Ø138 mm × 316 mm) |
| Mounting Dimensions / Bolt Pattern | 17.0 in × 2.5 in × 7.6 in (431 mm × 64 mm × 192 mm), 8 × M14 |
| Net Weight | 360 lb (163 kg) |
Applications
Service Truck Lifting : Mounts directly onto custom davit cranes or articulating crane arms on field service mechanics' trucks to lift heavy engine blocks, transmissions, and industrial pumps.
Tool and Equipment Loading : Installed on utility truck beds to effortlessly hoist heavy weld packs, gas cylinders, and tooling boxes from the ground up onto the vehicle platform.
Overhead Gantry Systems : Affixes to overhead I-beam trolleys or fixed gantry frames to hoist heavy machinery parts, steel fabrications, and raw materials over assembly lines.
Vehicle Maintenance Lifting : Utilized in automotive or heavy equipment workshops to suspend or precisely position unyielding sub-frames and assemblies during repairs.
Watercraft Hoisting : Integrated into dockside davits or small marina cranes to vertically lift jet skis, tender boats, and outboard motors out of the water for dry storage or servicing.
Marine Cargo Handling : Handles loading and unloading operations on utility vessels and cargo docks where a fully sealed, weather-resistant hoisting unit is required.
Heavy Farm Rigging : Mounts inside barns or specialized tractor attachments to safely suspend heavy farm implements, cutter decks, or tractor components for routine blade sharpening or structural maintenance.
Game and Timber Processing : Used on rural work yards to lift large timber logs onto processing benches or hoist large game carcasses onto cleaning racks.
HWP 20000YD winch are typically packaged securely to prevent damage during transit. The packaging includes:
Protective Wrapping: To safeguard the pump from environmental damage.
Custom Crates: For larger, heavier pumps, ensuring safe handling.
Documentation: Includes installation, maintenance instructions, and warranty details.
Delivery time depends on the model, customizations, and location but typically ranges from 2 to 6 weeks from the order date.
Answer : It is custom-tailored for heavy commercial flatbed wreckers, tilt-tray recovery tow trucks, agricultural machinery haulers, and massive 4x4 expedition rigs (eg, Unimogs) . Due to its immense raw torque and substantial structural mounted mass, it cannot be onto standard consumer light-truck front suspensions.
Answer : No. An industrial 9-ton winch demands up to 75 L/min fluid flow and a high 17.5 MPa pressure layout to reach full capacity. Standard consumer light-truck steering systems cannot provide this massive fluid volume. It must be plumbed into a dedicated PTO (Power Take-Off) system or an auxiliary high-output commercial pump loop.
Answer : Use High Gear (6:1 reduction) for fast unweighted cable deployment or retrieving light, rolling trailer assets quickly to save time on the job site. Shift into Low Gear (39:1 reduction) before conducting heavy, high-resistance vehicle extractions to maximize the raw mechanical torque of the planetary gear train.
Answer : Yes, it is exceptionally safe for synthetic Dyneema lines because hydraulic winches generate zero internal drum friction heat compared to electric units. However, for commercial towing and abrasive flatbed recovery work, maintaining heavy-duty steel wire rope is generally preferred to resist severe grinding, pinching, and fraying against damaged steel chassis components.
Answer : Because hydraulic systems are driven entirely by fluid pressure rather than direct wiring, you must source a hydraulic control valve kit . To operate the winch via handheld or wireless remotes, you will need an external directional control block valve (available in 12V or 24V variants depending on your truck's grid), high-pressure fluid lines, and a counterbalance valve to protect the motor circuit.
6. Do you provide OEM or customized services
Yes, we support OEM and customization, including nameplate, packaging, and specific performance requirements. Send us your drawings or specifications for evaluation.
HWP 20000YD winch are manufactured in compliance with international standards, ensuring high performance and reliability:
ISO 9001: Certified for quality management systems.
CE Certification: Ensures compliance with European safety, health, and environmental protection standards.
RoHS Compliance: Ensures the winch does not contain hazardous materials.
Factory Testing: Every winch is rigorously tested for performance, pressure, and leak integrity before shipping.
1.What's our advantages?
Factory established in 2005;
With a great deal of production experience;
80+ employees become the professional team;
Constant updated ERP system ensure efficiency of work;
Sophisticated equipment ehanced the accuracy of products;
Professional salesmen provide the greast service;
With a large number of famous customers all over the world;
Great after-sales service;
With the long term cooperation with famous logistics and express company in China,provide the better goods service.
Small order/sample order,full payment in advance; Big orders send the first payment 30% before the production,and the balance before shippment.We'll show the photos of the products and packages before delivery.
Of course we can. Just send me your logo we can make it for you.
America(40.5%):USA, Canada, Argentina, Brazil
Europe(30.8%):Italy,Germany,England,Holland,Spain,Swiss,Finland,Russia,Poland.
Asia(23.5%):Korea,singapore,India,Turkey,Vietnam,Saudi Arabia,Syria, Israel,Lebanon.
Others(5.8%).
The Cissoko hydraulic pump manufacturing facility is a specialized industrial plant that focuses on producing hydraulic pumps and related components. These factories are equipped with advanced machinery and technology to fabricate high-quality pumps designed for a wide range of applications, from heavy equipment and machinery to automotive and industrial systems.
The production process typically involves precision engineering, where raw materials like metals and alloys are processed into pump components such as gears, pistons, cylinders, and seals. These parts are then assembled into fully functional hydraulic pumps, which are tested for performance and quality control to ensure reliability, efficiency, and durability under various working conditions.
Cissoko Hydraulic's manufacturing facilities for hydraulic pumps maintain stringent quality standards, often adhering to international certifications, to meet the expectations of customers in industries such as construction, agriculture, automotive, and manufacturing.
All hydraulic pumps produced by Cissoko Hydraulic have undergone compliance testing, ensuring their quality and reliability.
To meet the diverse needs of different industries, the Cissoko hydraulic offer customization options, such as specialized seals, materials, and pump configurations. These facilities often work closely with engineering teams to develop tailored solutions for specific applications, from high-pressure systems to low-flow, high-efficiency pumps.
Each pump undergoes a rigorous quality control process, where pressure tests and performance assessments are conducted to ensure that the pumps meet the required standards for flow rate, pressure capacity, and durability.
